The Novak Guide to the
New Process 435 Transmission
The 435 is an excellent, heavy-duty truck transmission designed and used in ½, 3/4 and 1+ ton trucks. It is a well-built transmission and remains easy to locate and generally inexpensive to buy and maintain. The strength, relatively short size and the gearing of the transmission make it a good choice for a variety of situations.
The NP435 was made by New Process Gear from 1964 thru 1997. They are found primarily in Ford trucks from 1966 to 1992 and Dodge trucks from 1964 to 1993. They also had limited distribution in GM & Chevrolet trucks from 1968-1972. They are also found in some IH and industrial applications.
Identification
This transmission is 10.8" long and features an aluminum top cover that is retained by eight bolts. The NP435 case is of cast iron.
The Ford NP435 has a 1-1/16" diameter, ten spline input shaft that has a stick-out of 6-1/2" from the front face of the transmission. The pilot tip of the transmission measures ~17mm. The front bearing retainer flange measures 4.85" and the bearing retainer tube is 1.43" in diameter. The front bolt pattern is the symmetrical Ford "butterfly" pattern; roughly 8-1/2" wide by 6-5/16" tall. The input shaft stick-out length is 6-1/2".
The Dodge NP435 has a 23 spline input shaft with an 8-3/8" stickout. The Dodge NP435 featured two different styles of front input shaft & bearing retainer. The earlier and less common style (from 1966-1969, generally) used a deep ball roller bearing input. These earlier units are not compatible with our conversion assemblies. While ball bearing front versions still persisted in some applications, they were rare after 1969. The more common and later style featured a tapered roller bearing and cup assembly. These later versions are compatible with all of our adapter assemblies.
The GM / Chevrolet NP435 has a 10 spline input shaft with a 6-1/2". This version was only available with the roller style input bearing instead of the later and more common tapered bearing design. None of the GM NP435's are compatible with our adapter assemblies.
The shifting pattern for all of the 435's is in the standard "H" pattern with reverse gear being to the right side, and down.
| 1st | 2nd | 3rd | 4th (direct) | Rev. | |
| NP435A (Dodge, GM) | 4.56 | 2.28 | 1.31 | 1.00 | 5.64 |
| NP435L (Ford, Dodge, GM) | 6.68 | 3.34 | 1.66 | 1.0 | 8.26 |
| NP435D (GM) | 4.90 | 2.29 | 1.19 | 1.00 | 6.06 |
| NP435E (Ford) | 6.68 | 3.34 | 1.74 | 1.00 | 8.26 |
 |
Features
The NP435 is a top loaded, top shifting truck style transmission. The NP435 enjoys a very low compound gear at 6.68:1 and as such it is a popular choice for those wanting a very low crawling gear. Note that some Dodge versions of this transmission offered a taller first gear of 4.56-to-1.
The NP435 features a power-take-off (PTO) port on the passenger side of the case.
Transfer Case Adaptability
This transmission makes an excellent conversion transmission due to its adaptability into most Jeeps. Both 2wd and 4wd versions of the NP435 can be used equally well, and there are no inherent advantages to either one once you have installed our adapter assembly.
The Ford and Dodge 435 can be adapted to the popular Jeep (and many IH) transfer cases, including the:
-
A turn-key NP435, professionally built, adapted and delivered to your door - ready for a variety of engines and Jeep transfer cases. Read more... Dana 18, 1941-1971
-
Dana 20, 1962-1979
-
Dana 300, 1980-1986
 2wd & divorced 4wd & Dana 21 adapter pattern |
 4wd (married) adapter pattern |
There are two-wheel-drive and four-wheel-drive models; the critical difference being in the bolt pattern of the rear adapter housing or tail housing. Ford 4wd trucks with the remote (commonly termed "divorced") mounted transfer cases actually have the two-wheel-drive bolt pattern on the rear face and the installer should make this distinction when ordering the adapter assembly. Of note, the NP435's as married to the Dana 21 (single-speed transfer case) featured the 2wd pattern.
The Chevy / GM versions of the NP435 is different in its design, fairly rare and we do not support these adaptations. The installer can consider the SM465 for as a very good alternative.
 The front face bolt pattern of the Ford NP435. This particular version has been cast without the extra, undrilled ears that are useful when adapting to a GM bellhousing. |
Engine Compatibility and Adaptability
Dodge & Ford
As the reader will conclude, the Dodge NP435 will marry directly to a Dodge style bellhousing. Likewise for the Ford NP435 and its bellhousing compatibilities.
AMC Jeep
The Ford NP435 is also an excellent candidate for AMC Jeep bellhousings made from 1976 to 1986 that were married to the T150, T18 and T176 transmissions, or otherwise have an available bellhousing bolt pattern of 8-1/2" wide by 6-5/16" tall. They are readily compatible with these engines and bellhousings, and need only a custom pilot bushing. For more details, see Adapting Ford Transmissions to AMC Bellhousings for details.
GM
Many of the Ford NP435's have two extra undrilled ears cast into the front face of the transmission case. This is important if you intend to run it behind a GM bellhousing. The transmission having these extra undrilled ears will greatly simplify its use with GM engines. For more details, see Adapting Ford Transmissions to GM Bellhousings.
A Cautionary Issue on Towing If you must flat-tow, and have a transfer case, you may set it in full neutral and place the NP435 in any gear to prevent mainshaft spin. However, note that many transfer cases themselves do not allow for flat towing. Preferably, you may wish to disconnect the rear drive shaft. Rear axle lockout hubs may be a worthwhile addition for this reason. We have seen and heard of a few incidents of this over the years, the worst of which producing a complete friction welding of third gear to its mainshaft. This is one of the only quirks of the 435, and easily avoidable. |
Rebuilding the NP435
The NP435 is relatively simple to rebuild. Many shadetree mechanics do very outstanding rebuilds if they have access to a press, snap ring pliers and bearing pullers. Many choose to do a full rebuild during the adaptation process, and our instruction guides feature all the details, diagrams, pics and tricks required to do professional level work.
 |
|
|